www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 1 of 9 s pec n o : ? ? s s p p e e c c i i f f i i c c a a t t i i o o n n customer product ? saw filter model no hdf 43 3.96 m smd - 3 m arking ? hdf4 39 prepared checked appro ved ? d a t e 200 6 - 5 - 11 ??? shoulder electronics limited ?? c ustomer received: c hecked ? approved d ate
saw filter hdf 43 3.96 m smd - 3 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 2 of 9 ?? history record date spec . no . ?? part no . ??? customer no . m odify content ? remark
saw filter hdf 43 3.96 m smd - 3 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 3 of 9 1 .package ceramic package qcc8c marking hdf 4 39 hd: brand f : filter 4 39 : no. dimensions in mm, ap pr. weight 0.1g 2. performance 2.1 absolute maximum ratings rating value units incident rf power +13 dbm case temperature - 40 to +85 dc voltage between any two pins (observe esd precautions) 30 vdc pin configuration 1 input 2 input ground 5 output 6 output ground 4, 8 case ? ground 3.7 ground
saw filter hdf 43 3.96 m smd - 3 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 4 of 9 2.2 electrical characteristics reference temperature: t a = 25 terminating source impedance: z s = 50 and matching network terminating load impedance: z l = 50 and matching network characteristic min. typ. center frequency f c (center frequency between 3db points) -- 433.9 6 -- mhz insertion loss il -- 3.0 5.5 db 3db passband bw 3 300 khz 3 db reject band bw 3 500 khz at f c - 21.4mhz(image ) 40 50 -- at f c - 10.7mhz(lo) 15 30 -- rejection ultimate -- 80 -- db operating case temperature tc - 35 +85 turnover temperature to 15 25 40 turnover frequency fo fc mhz temperature frequency temperature coefficient ftc 0.032 ppm/ frequency aging absolute value during the first year |fa| 10 ppm/yr
saw filter hdf 43 3.96 m smd - 3 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 5 of 9 caution: electrostatic sensitive device. observe precautions for handling! 3. matching network to 50 (ele ment values depend on pcb layout and equivalent circuit) cp1 =10pf, ls2 =43nh * , ls3 =43nh * , cp4 =10pf ls2 = ls3 = 6 turns of 0.51mm insulated copper,2.5mm id. 4. typical frequency response
saw filter hdf 43 3.96 m smd - 3 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 6 of 9 5. environmental characteristics 5 - 1 tem perature cycling subject the device to a low temperature of - 40 for 30 minutes. following by a high temperature of +25 for 5 minutes and a higher temperature of +85 for 30 minutes. then release the device into the room conditions for 1 to 2 hours prior to the me a surement. it shall meet the specifications in 2.2 . 5 - 2 resistance to solder heat submerge the device terminals into the solder bath at 260 5 for 10 1 sec. then release the device into the room conditions for 4 hours. it shall meet the specifications in 2.2 . 5 - 3 solderability submerge the device term inals into the solder bath at 245 5 for 5s, more than 95% area of the soldering pad must be covered with new solder. it shall meet the specifications in 2.2 . 5 - 4 mechanical shock drop the device randomly onto the concrete floor from the hei ght of 1 m 3 times. the filter shall fulfill the specifications in 2.2 . 5 - 5 vibration subject the device to the vibration for 2 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 hz. the filter shall fulfill the specifications in 2.2 . 6. remark 6.1 static voltage static voltage between signal load & ground may cause det e rioration &destruction of the component. please avoid static voltage. 6.2 ultrasonic cleaning ultrasonic vibration may cause det e ri oration & destructio n of the component. please avoid ultrasonic cleaning 6.3 soldering only leads of component may be soldered. please avoid soldering another part of component. 7. packing 7.1 dimensions (1) carrier tape: figure 1 (2) reel: figure 2 (3) the pr oduct shall be packed properly not to be damaged during transportation and storage.
saw filter hdf 43 3.96 m smd - 3 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 7 of 9 7.2 reeling quantity 1000 pcs/reel 7?? 3000 pcs/reel 13?? 7.3 taping structure (1) the tape shall be wound around the reel in the direction shown below. (2) label device name user product name quantity lot no. (3) leader part and vacant position specifications.
saw filter hdf 43 3.96 m smd - 3 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 8 of 9 8. tape specifications 8.1 tensile strength of carrier tape: 4.4n/mm width 8.2 top cover tape adhesion (see the below figure) (1) pull off angle: 0~15 o (2) speed: 300mm/min. (3) force: 20~70g [figure 1] carrier tape dimensions [unit:mm] w f e p0 p1 p2 d0 d1 t1 t2 a b 12.0 0.3 5.5 0.05 1.75 0.1 4.0 0.1 8.0 0.1 2.0 0.05 ?1.5 0.1 ?1.0 0.25 0.3 0.05 2.10 0.1 6.40 0.1 5.20 0.1
saw filter hdf 43 3.96 m smd - 3 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 9 of 9 [figure 2] [unit:mm] a b c d e w t r ? 330 1.0 ? 100 0.5 ? 13 0.5 ? 21 0.8 2 0.5 13 0.3 3 max. 1.0 max.
|
